Porter Cable’s redesigned angle nailer fires standard 15-gauge angled finish nails and brings along a list of improved features and benefits. For starters, Porter-Cable upped the nail capacity, taking nails from 1 inch to 2-1/2 inches. The streamlined body balances the ample magazine in the center of the handle rather than off to one side, offering better balance than most of its competitors. Another nice redo: the angled coupler minimizes interference with the air hose during reloading. The tool’s weight is down, too, from 6 pounds down to 4.2 pounds, thanks in part to a new Teflon cylinder and a high-impact plastic magazine. The magazine loads from the rear with a by-pass pusher you can reach from either side of the tool. A non-marring rubber nose tip (with on-tool storage) will protect your workpiece. This nailer comes with a restrictive trigger, but a bottom-actuated trigger kit is available from Porter Cable.--Kris Jensen-Van Heste
With so many on offer these days, it is great to have a name you can trust. This item is certainly that and will be a perfect buy. The distributor have added some great touches and this equals great value.
You can trust this review, i hope you can try to buy this product and then you know this product good or no. Next time you can make a review for another people.
Could be better
12/9/04 My company owns 3 of these and they really do have a strong shot. We had no problems with getting the nails to set in the toughest materials. Our problems came after 8 mos of use. One of the units began having frequent jams and then started misfiring on a consistent basis. I'm a little concerned because another one of our DA250B nailers has also become somewhat unpredictable and sometimes jams. I definitely recommend the DA250B over the Senco SFN 35 or any Bostich nailers. The Senco SFN 30 and 40 are OK units. My top pick however is the Dewalt Angled Finish Nailer D51275K. All of our crews like this nailer over any of the finish nailers we've used. (Bostich, Porter Cable DA250B, Senco SFN 35, 40, 30). I will say that for the infrequent user either The Porter Cable DA250B or Dewalt D51275K will perform nicely.
Note: We use these finish nailers primarily in oak but sometimes in wood species such as Brazilian Cherry, Mahogany, Rosewood, Maple and other exotic wood...
Click here to read the full review for more information about this product.
This tool is more powerful, than the 16 gauge finish nailer
I have been using Porter Cables 16 gauge finish nailer, and their 18 gauge finish brad nailer, for over a year now. It has performed great. I was doing some tongue and groove cedar on a wall, and wasn't able to get a the nail on the 16 to sit down flush in the upper corner of the tongue. I picked up one of these 15 gauge, the new DA250B, and this thing kicks butt. It is substantially more powerful, than the 16 gauge. POW, their is no mistake about it. What that amounted to, was the 16 gauge would not drive the nail all the way into the inaccessable corner of the tongue. When I tried it with the 15 gauge, it drove the nail in further, all the way to clean with the surface, down in the corner. The 16 gauge took it to the extent the tip would go, but the 15 gauge went beyond the restriction, all the way to a flush finish. So you could say, the tongue extends out farther on the 15, like beyond flush. It is not the air pressure, I'm running it on a 6HP 60 gallon tank, or the setting of...
light and right
I just bought this finish nailer this weekend and love it. I was putting kithchen cabinets and trim together and needed to use the whole range of nail lengths (1 - 2.5"). I used the depth-of-setting gauge several times and that was easy. It's got a soft air blow out which you can adjust the direction on w/o an allen wrench. It's light weight, really light, compared to most that I use on the job but feels solid at the same time. The 15ga nails are remarkably strong and that will be helpful when casings help to set jambs. Besides the overall ease of use (e.g. loading and changing nails) I appreciate the single-firing trigger... It is quite a safety feature which does not allow you to fire if you're depressing the trigger just a bit before you engage the plunger: less chance of double firing, less chance of accidents.
Rating : 4.3
List Price : $358.38
0 comments:
Post a Comment