Porter-Cable FCN200 Pneumatic Flooring Cleat Nailer Discount !!

The Porter-Cable FCN200 Two-Inch Flooring Cleat Nailer drives 1-1/2 to 2-inch cleat nails quickly and efficiently. Durable and built to last, this nailer features a 100-cleat, rear-load, gravity-feed magazine with bypass pusher, and it has a well-balanced, stable design for dependable results in both traditional and engineered hardwoods.

The Porter-Cable FCN200 Two-Inch Flooring Cleat Nailer At a Glance: Drives L-shaped cleats from 1.5 inches to 2 inches Pneumatic driving action of 70-100 PSI Strong, lightweight aluminum housing Ergonomic design No assembly required

Durable, lightweight aluminum construction is heavy-duty without sacrificing comfort.

Balanced, Ergonomic, and Powerful
The FCN200 features a balanced, ergonomic design, and it stands upright for easy, stable use. It also has a low center of gravity that allows it to stand independently without falling over.

And because the FCN200 is made from durable, lightweight die-cast aluminum, it's heavy-duty enough to complete tough jobs, yet comfortable enough for extended use.

The FCN200 uses a compressor to provide air at approximately 70-100 PSI. It weighs just 13 pounds and arrives preassembled with an angled air hose nipple.

L-Shaped Cleat Extends Floor-Life
Whereas traditional flooring nailers use staple fasteners that don't allow for wood expansion and can shorten the life of a floor, the FCN200 utilizes an L-shaped cleat as its fastener. This cleat allows the floor to contract and expand naturally, even as it holds the floor in place.

And because standard 3/4-inch-thick solid hardwood flooring requires 2.0-inch cleats for secure installation, the FCN200 accepts cleats measuring from 1.5 to 2.0 inches. This means you can handle flooring materials of various thicknesses, including thinner engineered woods.

Additionally, the hammer head is short enough to allow the compressor to get close to the wall for installation of starting rows.

What's in the Box
FCN200; mallet; oil; wrenches; and 1/4-inch air fitting with dust cover.

With so many on offer these days, it is great to have a name you can trust. This item is certainly that and will be a perfect buy. The distributor have added some great touches and this equals great value.
You can trust this review, i hope you can try to buy this product and then you know this product good or no. Next time you can make a review for another people.

Excellent
This is a great must have tool for DIY wood floors. While every company that's in the tool business seems to make a nailer (Senco, Bostitch, etc.), what sets the Porter-Cable apart is it's balance and civilized look. The look doesn't matter, but if you don't want to mar the wood floors by having a tool keel over and damage the floor, then this is the tool to get.

The "last nail" comment is a very true. If you try to drive that single last nail, unpredictable results may occur. In my case, I had to throw the piece away (actually cut it for the closet), since the last nail went in almpst parallel to the surface of the wood and skimmed the finish off the top. If the wood hadn't been there, it probably would have shot across the room.

Finally, although the pneumatic nailers save you from backbreaking hammering, the nose takes more than just a light tap. A slightly sharp wack will drive the nails perfectly. Too soft and the nails don't get driven all the way...

Click here to read the full review for more information about this product.

Last cleat symptom
I read another review of the last cleat problem. I had several instances where the last cleat damaged the job before I realized what was happening, the tool also "dropped out" as many as four of the last cleats. One set of four got jammed in the mech. and was necessary to disassemble tool.I called the Porter Cable factory they said, "never heard of that problem, the tool should drive the last cleat".They did reccommend that I take it for warranty repair. I examined the pusher mechenism and could see the reason as the pusher does not go completely forward to push cleat against wall of dispenser. The pusher also hangs up at the last four or five cleats because of the latching arrangement causing the cleats to drop out. A visit to my local tool store showed the same conditions on the same model. I am using the tool to install brazilian cherry which is very hard, there is no problem in that respect it drives the cleats home every time and the tool is easy to use. I have been using Porter...
Porter-Cable FCN200 2" Flooring Cleat Nailer
Excellent nailer. I have laid over 1,500 feet of flooring with 2 jambs. It takes about 45 seconds to clear a jamb using the provided tool. Also the last nail in a set from Porter Cable seems to eject about 20% of the time which is not a big deal to me. Tells me to fill up. I let someone who used a hammer nailer use this one and he could not believe how fast and how much more power he got from the floor nailer.
After using for a few days and since the 2 jambs I have not had any additional problems. Senco nails for me are better than the Porter Cable. Senco nails have a glue that keeps them together where as the Porter Cable break like staples in your pocket or pouch. Overall an excellent tool but for $400 plus what do you expect. If you are on the fence over various brands go with Porter Cable. The nails are available locally and the tool performs well.

Product Features :

• Drives -inch shape cleat nails from 1-1/2-inch to 2-inch
• Pneumatic driving action consistently drives fastener for better finished installation
• Unit comes fully assembled and ready for use right out of the box
• Strong, lightweight, die-cast aluminum housing
• Non-marring base allows user to drive fastener close to wall; Better balance for stability - tool sits upright for smoother floor installation

Rating : 4.8
List Price : $1,021.92

Available at Amazon : Check Saved Price Now !

Categories: Cleat, FCN200, Flooring, Framing Nailers, Nailer, Pneumatic, Porter-Cable